清理沸石轉輪堵塞的方法主要包括以下幾種：

　　The methods for clearing blockages in zeolite wheels mainly include the following:

　　毛刷清理 ：

　　Brush cleaning:

　　使用直徑在0.3 ~0.5 mm 的尼龍絲束垂直刺入轉輪表面，破壞堵塞物與轉輪孔壁的黏結，使堵塞物脫離轉輪且不傷害轉輪結構。為提高效率，可以將平面毛刷改造為滾筒型，并配備手柄，通過滾動動作清理轉輪表面。

　　Use nylon fiber bundles with a diameter of 0.3~0.5 mm to vertically pierce the surface of the wheel, breaking the adhesion between the blockage and the wheel hole wall, allowing the blockage to detach from the wheel without damaging the wheel structure. To improve efficiency, the flat brush can be transformed into a drum type and equipped with a handle to clean the surface of the wheel through rolling action.

　　壓縮空氣吹掃 ：

　　Compressed air blowing:

　　使用日常使用的壓縮空氣（壓力最高為0.8 MPa）對轉輪進行吹掃，雖然可以吹出少量堵塞物，但效果不佳。因此，通常需要結合其他方法使用。

　　Using daily compressed air (with a maximum pressure of 0.8 MPa) to blow the impeller, although it can blow out a small amount of blockage, the effect is not good. Therefore, it is usually necessary to combine other methods for use.

　　毛刷和壓縮空氣結合 ：

　　Combination of brush and compressed air:

　　步驟一 ：用毛刷對轉輪表面進行滾刷，直到將堵塞物與轉輪的黏連狀態打破，注意不要使用毛刷在轉輪橫向摩擦，以免損壞轉輪。

　　Step 1: Use a brush to roll the surface of the wheel until the adhesion between the blockage and the wheel is broken. Be careful not to use the brush to rub laterally on the wheel to avoid damaging it.

　　步驟二 ：用壓縮空氣從反方向?qū)D(zhuǎn)輪進行吹掃，壓縮空氣壓力根據轉輪實際耐受力設定，原則上在不損壞轉輪的前提下越大越好。

　　Step 2: Blow the rotor in the opposite direction with compressed air. The compressed air pressure is set according to the actual tolerance of the rotor, and in principle, the larger the pressure, the better without damaging the rotor.

　　步驟三 ：對過濾箱和轉輪前后進行深度清潔，避免清理出的堵塞物再次進入轉輪。這種方法可以取得良好的效果，使轉輪壓差從2000 Pa 降為800 Pa 左右，轉輪效率提升至98%。

　　Step 3: Thoroughly clean the filter box and the front and rear of the impeller to prevent any blockages from entering the impeller again. This method can achieve good results, reducing the pressure difference of the impeller from 2000 Pa to around 800 Pa and increasing the impeller efficiency to 98%.

　　建議根據具體情況選擇合適的清理方法，并嚴格按照步驟操作，以確保轉輪的高效運行和延長使用壽命。

　　It is recommended to choose the appropriate cleaning method according to the specific situation and strictly follow the steps to ensure the efficient operation of the wheel and extend its service life.

　　本文由沸石轉輪＋CO提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.shtzxx.cn，我們將會全心全意為您提供滿意的服務。

　　This article is supported by zeolite wheel and CO technology. For more detailed and exciting content, please click on our website http://www.shtzxx.cn We will wholeheartedly provide you with satisfactory service.