中央木工除塵設備的設計：

Design of Central Woodworking Dust Removal Equipment:

1.在除塵設備出風口與風機的進口聯接我們設計為軟聯接，以消除因風機高速運轉帶來的震動；在風機的出口設計有消聲器，以降低因風機高速運轉產生的噪聲；

We have designed a soft connection between the air outlet of the dust removal equipment and the inlet of the fan to eliminate vibration caused by high-speed operation of the fan; A muffler is designed at the outlet of the fan to reduce the noise generated by high-speed operation of the fan;

2.為方便對除塵設備的檢修與觀察，我們在除塵設備灰斗下部設計有有機玻璃觀察（檢修）門；系統管道4-6米之間采用法蘭連接，5m左右設計有檢修門；便于觀察管道里面粉塵沉降的情況及清理；

For the convenience of maintenance and observation of dust removal equipment, we have designed an organic glass observation (maintenance) door under the ash hopper of the dust removal equipment; The system pipeline is connected with flanges between 4-6 meters, and a maintenance door is designed around 5 meters; Easy to observe and clean the dust settling inside the pipeline;

3.針對木材粉塵的親水特性，粉塵在有一定的水分的含量下容易結塊，在除塵設備灰斗里面架拱成橋導致堵料現象，我們在除塵設備灰斗設計有振動器，進行輔助清灰，減少人工輔助清灰的工作；

3. In response to the hydrophilic characteristics of wood dust, dust is prone to clumping at a certain moisture content, which can cause blockage in the ash hopper of the dust removal equipment. We have designed a vibrator in the ash hopper of the dust removal equipment to assist in cleaning and reduce the need for manual cleaning;

4.除塵設備電氣控制

4. Electrical control of dust removal equipment

通風除塵設備需要配套風機和空氣壓縮機，驅動需要三相四線制的電源，除塵設備清灰要配用1臺脈沖控制儀。脈沖儀安裝在除塵設備的附近。控制柜（箱）的電源由建設方提供相關。要求將電纜拉至控制柜內總開關上樁。同時請提供公共接地極，方便地線連接。

Ventilation and dust removal equipment requires supporting fans and air compressors, and the drive requires a three-phase four wire power supply. The dust removal equipment needs to be equipped with one pulse controller for dust cleaning. The pulse meter is installed near the dust removal equipment. The power supply for the control cabinet (box) shall be provided by the construction party. Request to pull the cable to the main switch in the control cabinet. Please also provide a common grounding electrode for easy connection of the ground wire.

5.針對木材粉塵濃度大的特點，除塵設備采用漸變的氣流通道設計，保證氣流均勻分布。對氣流組織進行優化設計，避免對除塵設備內部局部區域高速沖刷與磨損。使清灰壓縮空氣做到所有濾袋均勻地噴吹與過濾，提高濾袋的整體壽命。

5. In response to the high concentration of wood dust, the dust removal equipment adopts a gradual airflow channel design to ensure uniform distribution of airflow. Optimize the design of airflow organization to avoid high-speed scouring and wear on local areas inside the dust removal equipment. Ensure that the compressed air for dust cleaning is evenly sprayed and filtered through all filter bags, thereby improving the overall lifespan of the filter bags.

6.防燃防爆，多重安全保障

6. Flameproof and explosion-proof, multiple safety guarantees

由于木工粉塵易燃易爆的特性，我們采用防靜電裝置、卸爆裝置、脈沖防堵塞裝置等有效設施，并安裝有消防噴淋系統 為安全應急使用，確保設備長期安全運行；管道安裝有啟動清灰閥，能防止管道堵塞，保證管道順暢。

Due to the flammable and explosive nature of woodworking dust, we have adopted effective facilities such as anti-static devices, explosion-proof devices, pulse anti blocking devices, and installed fire sprinkler systems for safe emergency use, ensuring the long-term safe operation of the equipment; The pipeline installation is equipped with a startup cleaning valve, which can prevent pipeline blockage and ensure smooth pipeline operation.

本文由中央除塵設備友情奉獻.更多有關的知識請點擊:http://www.shtzxx.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

This article is a friendly contribution from the Central Dust Removal Equipment For more information, please click: http://www.shtzxx.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message